หัวแอมป์กีตาร์ Marshall ORIGIN 20H เป็นหัวแอมป์กีตาร์แบบหลอดมีกำลังขับ 20 วัตต์, 3 ECC83 preamp tubes and 2 EL34 power tubes, Single channel, Single input, 3-band EQ, tilt, gain, boost, master volume, presence, Impedance 8, 16 ohms, DI output, Footswitch included

The Marshall ORI20H Origin 20W Valve Head embodies the very essence of what made the Marshall brand so popular, and combines it with modern technology to deliver their ”most expressive” amp ever. Its classic single channel setup offers a vintage feel, while its iconic ECC83 preamp valve and EL34 power valve combination provides the Origin Amp Head with a truly ”British” tonal character and breakup.

The intuitive control panel offers the perfect level of tone shaping, allowing players to create a whole host of organic soundscapes. Even when driven hard, the ORI20H cleans up nicely when your roll down the guitar’s volume.

Also equipped with special volume reduction tech, an FX loop, D.I. output, 8 ohms and 16-ohm speaker outputs, and footswitch capabilities, the Marshall ORI20H Origin Amp delivers everything a gigging 21st century musician needs.

Features:

• Packed with 3 ECC83 preamp tubes and 2 EL34 power tubes
• Separate Gain and Master controls for dialing in the right amount of crunch
• Presence knob and 3-band EQ for shaping your tone
• Unique Tilt control blends bright and normal sounds
• Switchable Low/Mid/High power enables high-output sounds at any volume
• Built-in FX loop makes integrating your pedalboard easy
• Footswitchable gain boost for adding extra punch to your solos

The post หัวแอมป์กีตาร์ MARSHALL ORIGIN 20H Tube Head Amplifier appeared first on soundspacethai.com.

หัวแอมป์กีตาร์ Marshall ORIGIN 50H เป็นหัวแอมป์กีตาร์แบบหลอดมีกำลังขับ 50 วัตต์, Single channel, Power switching high, medium and low output, 3-band EQ, tilt, master, presence, boost, Footswitchable FX loop, boost, Speaker outputs 3x 6.3 mm jack (16 ohms / 8 ohms)

The Marshall ORIGIN50H Origin 50W Valve Head features a single channel and a vintage style performance, delivering their ”most expressive” amp yet. Its 50 watts of pure rock ‘n’ roll power drives the ECC83 preamp valves and EL34 power valves, producing the classic ”British” tonal character and breakup. The intuitive control panel provides players with excellent tone shaping capabilities, offering a 3-band EQ, tilt, pull boost, and presence controls for dialling in classic Marshall tones.

The 50W Origin Amp Head is also equipped with a 3-way power output switch, offering the choice between 1W, 10W, and 50W of power to maintain the classic valve saturation at any volume.

The Marshall ORI50H Amp Head also features an FX loop, emulated D.I. output, footswitch capabilities, and a selection of loudspeaker outputs for connecting 8 ohms and 16-ohm speaker cabinets.

Features:

• Packed with 3 ECC83 preamp tubes and 2 EL34 power tubes
• Separate Gain and Master controls for dialing in the right amount of crunch
• Presence knob and 3-band EQ for shaping your tone
• Unique Tilt control blends bright and normal sounds
• Switchable 1W/10W/50W power enables high-output sounds at any volume
• Built-in FX loop makes integrating your pedalboard easy
• Footswitchable gain boost for adding extra punch to your solos

The post หัวแอมป์กีตาร์ MARSHALL Origin 50H Tube Head Amplifier appeared first on soundspacethai.com.

หัวแอมป์กีตาร์ Marshall DSL1HR เป็นหัวแอมป์กีตาร์แบบหลอดมีกำลังขับ 1 วัตต์ Dual-Channel Operation, Rear-Panel Output Switch (1 or 0.1W), 2 ECC83 Tubes & 1 ECC82 Tube, 1 x 1/4″ 16-Ohms Speaker Output Jack, Onboard Effects Loop, Digital Spring Reverb, Footswitch Controller Included

The Marshall Amplification DSL1HR is a two-channel amplifier head powered by three valves/tubes. One channel gives you a cleaner tone, while the other is suitable for your distortion needs. A three-knob tone stack, coupled with a tone shift button that reshapes the preamp’s EQ, helps you dial in your preferred timbre.

With a low-power switch on the back, you can reduce the output from 1W to 0.1W without affecting the tone. Thus, you can practice in your home with minimal disturbance to your family or neighbors.

An onboard effects loop gives you the ability to put your pedals or external processors directly in the amplifier’s signal path, while a reverb knob on the front panel allows you to apply some ambience to your signal.

An auxiliary input is on hand for jamming along to your favorite tunes. You can route your signal from the emulated output jack to headphones or to a recording interface, taking advantage of the Softube-designed studio-cabinet emulation all the while.

This amplifier head sports a single 1/4″ speaker output jack rated at 16 Ohms. You can use this amplifier with speakers such as the 160HM extension speaker cabinet, or you can use it as a front end for your interface’s DI input, using the emulated output jack in coordination with a 3.5mm-to-1/4″ adapter. A footswitch is supplied, with which you can choose between the two channels.

Features:

• Capable of conjuring any classic Marshall sound — past or present
• 2 channels — Classic Gain and Ultra Gain
• High and low power modes allow you to dial in appropriate volume for any setting
• Line output with Softube’s accurate emulation of a Marshall 1960 cab
• Refined EQ section gives you incredible tonal flexibility
• Studio-grade digital reverb
• Rear-panel series effects loop

The post หัวแอมป์กีตาร์ MARSHALL DSL1HR Tube Head Amplifier appeared first on soundspacethai.com.

หัวแอมป์กีตาร์ Marshall DSL120HR เป็นหัวแอมป์กีตาร์แบบหลอดมีกำลังขับ 20 วัตต์ 2-CH Classic Gain & Ultra Gain Channels, 3 ECC83 Tubes & 2 EL34 Tubes, Front-Panel Output Switch (20 or 10W), Digital Spring Reverb, Footswitch Controller Included

The post หัวแอมป์กีตาร์ MARSHALL DSL20HR Tube Head Amplifier appeared first on soundspacethai.com.

หัวแอมป์กีตาร์ Marshall DSL100HR เป็นหัวแอมป์กีตาร์แบบหลอดซึ่งออกมาแทนรุ่นเดิม DSL100H, 2-CH Classic Gain & Ultra Gain Channels, มีกำลังขับ 100 วัตต์ 4 x ECC83 Tubes & 4 x EL34 Tubes, Front-Panel Output Switch (100 or 50W), Digital Spring Reverb, Footswitch Controller Included

The Marshall Amplification DSL100HR is a 100W valve amplifier head for electric guitar, featuring two channels for Classic Gain and Ultra Gain. Though the amplifier offers many of the same features that made the previous model so popular—most notably, switchable channels with two modes apiece, as well as dual reverb controls—this amplifier improves upon the design of the DSL100H in several ways.

Most prominently, the amplifier head gives you two independent master volume knobs, so you can choose between two different overall volumes on the stage. This is quite useful for soloing, or for lead breaks, where you might want to be a little louder than normal. By means of a separately available six-button footswitch, you can change your volume with the tap of your toe.

MIDI connectivity has also been added, allowing you to integrate the amplifier with your MIDI-enabled gear or MIDI switchers. The power-reduction switch has also received an upgrade. Whereas the previous model sported a back-panel selector that flipped between pentode and triode operation, the DSL100HR boasts a front-panel rocker switch that works directly with the transformer, rather than the tubes. Thus, when you switch from 100W to 50W, you’ll experience no shift in tone.

Other differences include the addition of more 1/4″ outputs supporting various impedances, so you can use this amplifier work with 16-, 8-, and 4-Ohm cabinets. An emulated output offers a cabinet simulation design by Softube, and can be used in recording scenarios. You’ll note the switchable FX loop, as well as an auxiliary input.

Tonally, this amplifier is similar to the previous unit, with a wide array of classic marshall timbres on hand, from the sound of a 1959 Super Lead Plexi in clean mode to the growl of a JCM800. Another key difference, however, is the look of the DSL100HR. With elephant-grade tolex employed in its construction, you’ll find it resembles classic British-built Marshall amplifiers.

The DSL100HR ships with a power cord and a dual footswitch for Classic/Ultra channel selection and reverb on/off.

Features:

• Capable of conjuring any classic Marshall sound — past or present
• 2 channels — Classic Gain and Ultra Gain
• Each channel features two modes — Clean/Crunch and OD1/OD2, respectively
• High and low power modes allow you to dial in appropriate volume for any setting
• Line output with Softube’s accurate emulation of a Marshall 1960 cab
• Highly effective Resonance control replaces the original’s fixed deep switch
• Refined EQ section gives you incredible tonal flexibility
• Studio-grade digital reverb
• Bypassable rear-panel series effects loop
• Included 2-way footswitch for channel switching and reverb on/off

The post หัวแอมป์กีตาร์ MARSHALL DSL100HR Tube Head Amplifier appeared first on soundspacethai.com.

หัวแอมป์หลอดขนาดเล็กสำหรับกีตาร์ Peavey 6505 Piranha Micro Head, มีกำลังขับ 20 วัตต์ RMS, Tube-Driven Preamp with 1 x 12AX7 Tube, Lead/Crunch Switch, Drives Cabinets at 4 Ohms, Single EQ Control, Gain & Volume Controls, 1/4″ Speaker Output, Padded Carry Bag Included

Making use of a single 12AX7 tube for its preamp stage, The Peavey 6505 Piranha is an amplifier head intended for use with electric guitars. It supplies 20W RMS into 4-Ohm loads and provides a rather simple, yet powerful, control set. Three knobs are on hand to shape your volume and tone: Gain, EQ, and Volume. Gain controls the preamp stage, while volume dictates your overall level.

The solitary EQ knob is designed to shift between the timbre of classic Peavey amplifiers, helping you to achieve tones suitable for thrash, metal, conventional rock music, and more. The Crunch/Lead switch alternates between two different channel voicings.

In addition to a single 1/4″ instrument input, the 6505 Piranha sports a 3.5mm auxiliary input for looping in your media player or smartphone for jamming along to music, as is a headphone jack for practicing late at night without disturbing your neighbors. A 1/4″ speaker jack can be found on the rear of the amp, where you’ll also note a buffered 1/4″ I/O section for an effects loop. This amp can drive the Micro 1×8 cabinet, as well as the 112-6, 212-6, and even the 605 412. A padded carry bag is included for transporting the amplifier.

Features:

• 20W RMS, Drives Cabinets at 4 Ohms
• Tube-Driven Preamp with 1 x 12AX7 Tube
• Lead/Crunch Switch
• Single EQ Control
• Gain & Volume Controls
• 1/4″ Speaker Output
• 1/4″ Headphone Output & 3.5mm Aux Input
• Buffered 1/4″ Effects Loop
• Padded Carry Bag Included

The post หัวแอมป์กีตาร์ PEAVEY 6505 Piranha Head Guitar Amplifier appeared first on soundspacethai.com.

หัวแอมป์กีตาร์แบบหลอด MARSHALL 2525H Mini Silver Jubilee กำลังขับ 20 วัตต์ 2 ชาแนล, Pre amp valves 3 x ECC83, Power amp valves 2 x EL34, DI output, Effects loop

The post หัวแอมป์กีตาร์ MARSHALL 2525H Tube Guitar Amp Head appeared first on soundspacethai.com.

หัวแอมป์กีตาร์แบบหลอด MARSHALL JVM205H Tube Guitar Amp Head ขนาด 50 วัตต์, 2 channels, All-valve, with 5 x 12AX7s and 2 x EL34s, 2 FX loops, 4-way footswitch (with memory) supplied

In a nutshell, the Marshall all-valve, 2-channel JVM205H 50W tube head is a 2-channel, 50W version of the most versatile Marshall amplifier ever made, the JVM410H. Both channels are completely independent of each other and they boast 3 Modes, all 6 of which are footswitchable and feature their own unique gain structure. It effectively makes the JVM205H 6 Marshalls in one

The JVM205H has studio-quality digital reverb with a level control for each channel. This is also footswitchable, as are the amp’s two Master Volume controls and the Series/Parallel effects loop. Resonance and Presence are also equipped with master controls.

With its ingenious footswitch (UK patent pending) and the fact all the amp’s switching (channel/modes, Reverb, Master Volume selection, FX loop) can be done via MIDI, you’re looking at an incredibly flexible amp! The 4-way footswitch boasts LEDs and memory, plus it connects to the amp via a regular guitar cable.

From the cleanest clean to the filthiest distortion ever found in a Marshall and all points in-between, the JVM205H all-valve amp head will give you whatever tone

Features:

• 50W power
• All-valve, with 5 x 12AX7s and 2 x EL34s
• 2 totally independent, footswitchable channels
• Each channel has 3 footswitchable modes
• Footswitchable, studio-quality digital reverb
• Independent reverb controls for each channel
• 2 footswitchable master volumes
• 2 FX loops, one series, and one parallel
• Parallel FX loop is footswitchable on/off
• Speaker emulated XLR output
• 4-way footswitch (with memory) supplied
• All switching can be done via MIDI

The post หัวแอมป์กีตาร์ MARSHALL JVM205H Tube Guitar Amp Head appeared first on soundspacethai.com.

หัวแอมป์กีตาร์แบบหลอด MARSHALL JTM2245THW Handwired ขนาด 30 วัตต์ , 2-channel Handwired Tube Head with Tube-driven Tremolo, KT66 power tubes and a GZ34 tube rectifier

The all-valve 2245THW is a hand soldered re-issue of the extremely rare ‘Bluesbreaker®’ head, based on the archetypal JTM45 head, which was the amp that began it all back in 1962. As you would expect, the specifications for the 2245THW are identical to the 1962HW ‘Bluesbreaker’ combo, minus the speakers of course. Inside the 2245THW the valve set is four ECC83, with two KT66 in the power stage and a GZ34 rectifier.

It’s the GZ34 rectifier that helps create the sublime output stage compression and clean sustain associated with the ‘Bluesbreaker’ head. To make the 2245HW as authentic as possible, we have used original thickness, original pitch matrix, point to point tag boards. As with the ’Bluesbreaker’ combo, the 2245THW features valve-driven Tremolo.

Features:

• Accurate reissue of the legendary JTM45 amplifier, a ’60s rock legend
• Handwired in the U.K.
• 30 watts of power – perfect for gigging and recording
• A pair of KT66 power tubes and a GZ34 tube rectifier adds natural, smooth compression and sustain to your tone
• Tube-driven tremolo circuit for authenticity
• Sounds great with gain boost pedal in front of it

The post หัวแอมป์กีตาร์ MARSHALL JTM2245THW Handwired Tube Head appeared first on soundspacethai.com.

หัวแอมป์กีตาร์แบบหลอด MARSHALL JTM45 (2245-01) ขนาด 30 วัตต์, Clean tone, 3-band EQ, Preamp valves: 3 x ECC83, Power amp valves: 2 x 5881, GZ34 valve rectifier

The very first Marshall® amp, made back in 1962, was the JTM45. It was an instant hit and launched a whole new generation of groundbreaking guitar players and sounds. Since then, connoisseurs of tone have sought out rare original JTM45s from the ’60s. Now they shall seek no more, thanks to this meticulously accurate re-issue.

It was GZ34 rectification that was the key to the JTM45’s sound, and this is a feature painstakingly reproduced in this re-issue. The way the rectifier interacts with the other valves causes subtle harmonics to shift and smoulder beneath every note, producing the unmistakable, original, and much emulated Marshall sound.

Features:

• Accurate reissue of the legendary JTM45 amplifier, a ’60s rock legend
• 30 watts of power, perfect for gigging and recording
• GZ34 tube rectifier adds natural, smooth compression and sustain to your tone
• Sounds great with gain boost pedal in front of it
• Straightforward control set is all you need to craft a range of vintage ’60s guitar tones

The post หัวแอมป์กีตาร์ MARSHALL JTM45 Tube Guitar Amp Head appeared first on soundspacethai.com.